Affiliate Disclosure: This post contains affiliate links. When you purchase through these links, we may earn a small commission at no additional cost to you. This helps support the site's research and upkeep.

How to Fix a Scratchy or Dry Fountain Pen Nib (10x Loupe & Brass Shim Guide)

Tags:troubleshootingnib tuningscratchy nibdry nibbrass shimsloupemylar
By Fountain Pen Expert Team • Published November 19, 2026

Never sand a scratchy nib blindly: 80% of scratchy or dry fountain pens can be fixed safely in 5 minutes using a $25 DIY tuning kit—a 10x jeweler’s loupe ($10) to spot misaligned tines, 0.002" brass shims ($8) to floss clogged slits and boost ink flow, and 0.3-micron Mylar lapping film ($9) only for final micro-polishing.

Quick Buying Guide: The 3-Tool DIY Nib Tuning Kit (~$25 Total)

🔍 Step 1: Diagnose First (Mandatory)
10x Magnifying Glass

10x Jeweler’s Loupe ($9–12)

10x Magnifying Glass · Typical: $10-15

Best if: Instantly reveals whether your left and right nib tines are misaligned or pinched shut—impossible to see reliably with the naked eye.

Setup note: Hold the loupe close to your eye (not the pen) and bring the nib tip into focus about 1 inch away under bright light.

Check 10x Loupe on Amazon →
💧 Step 2: Fix Dry Flow & Clear Fibers
Brass Shims Set

0.002" Brass Shims Set ($7–9)

Brass Shims Set · Typical: $9-11

Best if: Slides gently through the nib slit to pull out microscopic paper fuzz and gently relax pinched tines for a wetter, smoother ink line.

Setup note: Use the thinnest 0.002" sheet first; never force or twist a thick shim or you will over-widen the slit.

Check Brass Shims Set →
✨ Step 3: Final Micro-Polish Only
Mylar Polishing Film 0.3 Micron Set

0.3-Micron Mylar Polishing Film ($8–10)

Mylar Polishing Film 0.3 Micron Set · Typical: $7-12

Best if: Ultra-fine abrasive sheet that buffs out minor roughness on already-aligned tipping to create a silky, glassy glide.

Setup note: Irreversible if overdone—never polish an unaligned nib, and test after every 3–4 light figure-eight strokes.

Check 0.3-Micron Mylar Film →
Waterman Serenity Blue

Diagnostic Reference Ink: Waterman Serenity Blue (50ml)

Always test a freshly tuned nib with a reliable, neutral-flow ink so you know whether flow issues come from the nib or a dry ink.

Symptom-to-Fix Diagnosis Table

Match Your Nib Problem to the Right Tool

What You Feel on PaperLikely CauseCorrect ToolSafe Action
Scratchy going left-to-right only (or right-to-left only)Misaligned tines (one tine sits higher)10x Loupe + fingernailsGently nudge the lower tine UP (or higher tine DOWN) for 3 sec; re-check
Skips, writes pale/dry, or stops mid-sentencePinched tines or trapped paper fiber in slit0.002" Brass ShimFloss gently from breather hole down through tip; pull straight out
Mild uniform grit in all directions (tines aligned)Slightly rough factory tipping polish0.3-Micron Mylar Film3–5 feather-light figure-8s with inked nib; wipe and test
Hard starts after sitting 1 day (tines fine)Factory oil in feed or dry inkFlush + Waterman InkFlush with water + 1 drop dish soap; refill with Waterman Serenity Blue

Quick Comparison

ProductBest For / RolePriceKey HighlightsAction
tool$10-15
  • ✓10x magnification
  • ✓Helps inspect nib alignment
Check Price
tool$9-11
  • ✓Nib tine cleaning
  • ✓Gentle alignment aid
Check Price
nib smoothing tool$7-12
  • ✓Very fine 0.3 micron abrasive surface
  • ✓Intended for tiny, controlled smoothing passes only
Check Price
bottled ink$8-12
  • ✓50ml bottle
  • ✓Dye-based formula
Check Price

The Safe 5-Minute Nib Tuning Sequence

  1. Flush first: Before touching any metal tool, flush the nib and feed thoroughly with cool water and a single drop of dish soap to strip factory oils.
  2. Inspect head-on with a 10x Magnifying Glass: Look straight down the tipping at a 45° writing angle. Both halves of the iridium ball should form a perfectly level, symmetrical horizon. If one side is higher, gently press the higher tine downward with your thumbnail for 2–3 seconds and re-check.
  3. Floss with a Brass Shims Set: If the pen still writes dry or catches paper lint, insert a thin brass shim at the breather hole and glide it straight out the tip. Repeat twice.
  4. Micro-polish last (only if needed): Only once alignment is 100% level, wet the nib with Waterman Serenity Blue and draw 3 gentle figure-eights on Mylar Polishing Film 0.3 Micron Set. Stop the moment it glides smoothly—over-polishing creates "baby’s bottom" skipping!

Frequently Asked Questions

What is the #1 cause of a scratchy fountain pen nib?

Roughly 80% of "scratchy" nibs are actually caused by misaligned tines—meaning one half of the nib tipping sits slightly higher than the other and scrapes the paper fibers in one direction. Always check tine alignment under a 10x loupe before ever touching an abrasive polishing sheet.

Can brass shims damage my fountain pen nib?

Used gently, a 0.002-inch brass shim safely clears trapped paper fibers and slightly opens overly tight tines to make a dry nib write wetter. Never jam thick shims repeatedly between the tines or twist the sheet sideways, which can over-widen the slit and cause ink blobs.

When should I use 0.3-micron Mylar lapping film on a nib?

Only use 0.3-micron Mylar polishing film AFTER you have verified under a 10x loupe that the tines are 100% aligned—and only if the nib still feels mildly toothy in all directions. Make just 3 to 5 light figure-eight strokes with an inked nib, then test on paper.

Should I try a wetter ink before physically tuning a dry nib?

Yes! Always flush the pen first (to clear factory machining oils) and test it with a known wet, well-behaved ink like Waterman Serenity Blue. Many "dry" pens write dramatically better after a single thorough flush and ink swap.

Related Guides & Reviews

Continue comparing options and side-by-side evaluations.

All Guides →